- 您现在的位置：买卖IC网 > Sheet目录470 > MAX11008EVC16 (Maxim Integrated)EVAL KIT MAX11008
Dual RF LDMOS Bias Controller with
Nonvolatile Memory
V GATE_ = (2 x V REFDAC x CODE)/4096
5) The V GATE_ equation is now calculated and
where:
= [2 x V REFDAC x (V SET _ + LUTTEMP{Temp} +
LUTAPC{APC})]/4096
depending on the status of the LDAC_ bit, output to
the appropriate DAC. The actual value of the DAC
output depends on the values within the LUT. It is
possible that the new value for V GATE_ is the same
V GATE_ = actual gate voltage.
V SET_ = factory-set DAC code at TCAL.
LUTTEMP{Temp} = interpolated lookup value in the
TEMP table for the sampled temperature.
LUTAPC{APC} = interpolated lookup value in the APC
table for the APC parameter.
TCAL = temperature at which LUTTEMP{TCAL} returns
0; i.e., the calibration temperature.
V SET_ is a 12-bit unsigned DAC code (0 to 4095).
LUTTEMP{Temp} and LUTAPC{APC} are the result of
lookup operations and are 16-bit signed numbers in
DAC CODE units. The MAX11008 calculates the sum of
(V SET_ + LUTTEMP{Temp} + LUTAPC{APC}) with 16-bit
signed arithmetic and limits that result to the 12-bit res-
olution of the DAC (0 to 4095) to arrive at the final out-
put DAC CODE.
The LUT values for Temp (LUTTEMP{Temp}) and APC
(LUTAPC{APC}) are the result of lookup table opera-
tions (LUT operations). The values are directly stored in
the LUT sections of the EEPROM. They are 16-bit
signed (two’s complement) quantities, but to prevent
mathematical overflow, their magnitude should be limit-
as the last value for V GATE_ , even though the hys-
teresis in step 2 was exceeded.
If averaging is enabled for either the temperature or
APC parameter, the V GATE_ calculation process is the
same. The difference is that the value for the ADC sam-
ple (step 1 and step 3) is replaced by an ADC average.
The MAX11008 measures 16 samples to acquire an ini-
tial average. When averaging is enabled, the first 15
samples do not trigger a new average, and a V GATE_
calculation is not triggered. After the average is
acquired, each new ADC sample produces a new
rolling average. The rolling average is calculated with
the following equations.
In acquire mode:
15
Average = ∑ Sample /16
j = 0
Average is only valid after 16 samples.
In tracking mode:
Average = 15/16 Average + 1/16 Sample
= 15/16 Average + 1/16 (Average + Difference)
ed to 12-bit quantities (-4096 to +4095, which is the full
range of the DAC ignoring the sign).
When averaging is disabled, V GATE_ operations pro-
ceed as follows:
where:
Difference = Sample - Average
= Average + 1/16 Difference
1) A new ADC sample is measured and compared to
the last sample used for a V GATE_ calculation.
2) The absolute difference between the two ADC mea-
surements is compared to the hysteresis setting. If
the difference is equal to or greater than the hystere-
sis setting, the new sample is used to recalculate
V GATE_ . If the hysteresis setting is not exceeded, the
following steps are bypassed and V GATE_ is not
recalculated.
3) The ADC sample is converted to a pointer for the
LUT. The mechanism for this is explained in the fol-
lowing section, but the process turns the 12-bit ADC
sample into an n-bit pointer.
4) The lookup operation is performed, and if required,
an interpolation between two table values is calcu-
lated. The result from the lookup table is stored as
either LUTTEMP{Temp} or LUTAPC{APC}.
= Average + 1/16 (Limited Difference)
The limited difference between the sample and the
average is a maximum value that is set by the T_LIMIT
and A_LIMIT bits, which are used to reject spurious
noise. Difference limiting may be set from 1 LSB to 64
LSBs, or may be disabled altogether.
By setting the A_AVGCTL and T_AVGCTL bits, the
average tracking formula can be altered to add 1/4 of
the difference on each calculation, rather than 1/16.
This reduces the filter’s time constant and allows the
average to track faster moving signals, and is most
suited to the APC channel. The A_AVGCTL and
T_AVGCTL bits do not alter the formula for acquiring
the initial average.
If the APC[11:0] value is used instead of an ADC sam-
ple for the APC sample, all averaging and hysteresis
functions are bypassed. The serial interface directly
controls the APC[11:0] value and triggers a V GATE_ cal-
culation each time it is written.
______________________________________________________________________________________
37
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MAX11014BGTM+T
IC RF MESFET AMP 48-TQFN-EP
MAX12000ETB+T
IC AMP GPS FRONT 1575MHZ 10TDFN
MAX12005ETM+T
IC SATELLITE IF SWITCH 48-TQFN
MAX1385BUTM+
IC RF LDMOS BIAS CNTRLR 48-TQFN
MAX1470EUI+T
IC RECEIVER 315MHZ 28-TSSOP
MAX1470EVKIT-315
EVAL KIT FOR MAX1470 315MHZ
MAX1471EVKIT-315
EVAL KIT FOR MAX1471 315MHZ
MAX1472EVKIT-433#
EVAL KIT MAX1472
相关代理商/技术参数
MAX11008EVKIT+
功能描述:放大器 IC 开发工具 MAX11008 Eval Kit RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V
MAX1100CWG
制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
MAX1101
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Single-Chip, 8-Bit CCD Digitizer with Clamp and 6-Bit PGA
MAX11014
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers
MAX11014_08
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers
MAX11014BGTM
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers
MAX11014BGTM+
功能描述:特殊用途放大器 Auto RF MESFET Amp Drain-Current Cntrlr RoHS:否 制造商:Texas Instruments 通道数量:Single 共模抑制比（最小值）: 输入补偿电压: 工作电源电压:3 V to 5.5 V 电源电流:5 mA 最大功率耗散: 最大工作温度:+ 70 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-20 封装:Reel
MAX11014BGTM+T
功能描述:射频放大器 Auto RF MESFET Amp Drain-Current Cntrlr RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel